CRC 6-66 Marine, 300ml

2-5 Päivää

Avaa galleria klikkaamalla

Ilmainen toimitus

Jos ostoksesi ylittää € 40,00, on kuljetus Viro sisällä meidän kustannuksellamme (Omniva ja SmartPOST).

Katsottu: 6858
Näytä lisää tuotteita samalta valmistajalta
Tuotenumero: SKU-2274
Saatavuus: 2-5 Päivää

€8.56
Veroton: €7.02

Määrä

Lisää toivelistaan Vertaa tätä tuotetta

0 arvostelua / Kirjoita arvostelu

Kuvaus
Arvostelut (0)

CRC 6-66 Marine

1. GENERAL DESCRIPTION

Multi-purpose marine lubricant and corrosion inhibitor.

CRC 6-66 is based on a paraffinic oil and a multiple organic inhibitor system that prevents rust and corrosion by displacing and sealing out moisture and by forming a continuous

protection barrier against water and oxygen. The oily, almost invisible film of CRC 6-66 lubricates and penetrates into the finest pores and cracks of the surface.

CRC 6-66’s effectiveness for surface protection is derived from three of its principal

properties:

• affinity for metal

• low surface tension

• high capillary action.

By its affinity for metal and low surface tension CRC 6-66 displaces moisture and separates it from contact with the metal surface. The high capillary action contributes to the great spreading power.

2. FEATURES

• Displaces and seals out moisture, especially after washing or hosing off engines or equipment.

• Penetrates through corrosion to loosen rusted parts.

• Lubricates without leaving a sticky residue.

• Protects against corrosion, even during storage.

• Stops squeaks.

• Starts wet engines.

• Prevents electrical failures.

• Cleans light soils and contaminants.

• Prevents 'fingerprinting' by its protective film.

• Protection of all metals and alloys.

• Compatible with most painted surfaces, coatings, plastics and rubbers.

• Equipped with the 360° (upside-down) spray valve for added convenience.

• Pressurised with non-flammable CO2 propellant.

• Active product content of 97%.

• Specification: NSN 6850 - 13 - 115 – 1885.

3. APPLICATIONS

• Ignition systems

• Distributors

• Battery terminals

• Engines

• Cables

• Plugs

• Switches

• Aerials

• Electrical and electronic equipment

• Generators

• Nuts and bolts

• Locks

• Hinges

• Chrome, outboard and inboard

• Steel

• Plated or painted surfaces

• Fishing gears.

4. DIRECTIONS

• Spray in light, even films to lubricate and protect metal surfaces. For electrostatic spraying, addition of polar solvents (butanol, nitropropane, ...) may be necessary.

• Apply liberally and allow to penetrate to free rusted parts. Full penetration may require several hours.

• To displace moisture, spray wet surfaces until run-off is clear and moisture-free.

• To be removed by solvent cleaners (CRC Industrial Degreaser, CRC Fast Dry Degreaser,…) or alkaline degreasing before surface treatment.

• For application of CRC 6-66 in dipping baths, customers should take care to stir from time to time (to distribute small amounts of deposits) and to prevent excessive evaporation of solvent.

When stable emulsions have been formed, the bath should be emptied and cleaned, and the product replaced.

• Do not use on energized equipment. Use in a well ventilated area.

• A safety data sheet (MSDS) according EU-Directive 93/112 is available for all CRC products.

5. TYPICAL PRODUCT DATA (without propellant)

Appearance : blue-green, clear

Specific gravity @ 20°C : 0.83

Distillation range of solvents : 190-250°C

Freezing point : -50°C

Flash point (open cup) : 78°C

Dynamic viscosity @ 20°C : 3.9 mPa.s

Ultimate film thickness : 2.10-6m.

(@ 20°C, after a 24 hr spread)

Maximum expected coverage : 100 m2/l.

(@ 20°C, after a 24 hr spread)

Solvent dissipation : 2-4 h.

Kirjoita arvostelu

Nimesi

Arviosi

HUOM: HTML-koodia ei käännetä!

Arvostelu Huono Hyvä

CRC 6-66 Marine, 300ml

Ilmainen toimitus

Kirjoita arvostelu

Liqui Moly Motor-Innen-Konservierer, 300ml

Motul Nautic Grease, 400gr

Motul Trans Lube 90, 350ml

Motul Nautic Grease, 200gr